Brick Paver Installation & Edging



Staging of material

Most paver tasks will vary depending upon access, website conditions, project size and naturally, the weather. These circumstances can have a general influence on your job from a timing stand point. Mindful factor to consider should be taken to figure out the time to begin the paver installation. Always attempt to reduce or prevent any traffic on the prepared areas.

The supervisor or project supervisor should always have the products (sand/ pavers) distributed around the job website for efficient and simple installations. Paver pallets/bundles must be placed in a manner not to hinder the paver installation. The proper pallet/bundle placement can make the real task installation easier and quicker by minimizing the overall labor of dealing with the product.

Brick paver patterns

Pavers can be placed in various patterns depending upon their shape. Each paver shape will generally have a number of various hatch patterns that are provided by the producer.

Contractors need to take into factor to consider the traffic weight loads on their paver tasks. In many applications around the world, it has actually been shown that pavers laid in a herringbone pattern have performed effectively.

Pavers that are 60 mm (2 - 3/8 in) thickness are suitable for pedestrian applications. Pavers that are going to be used in business or industrial applications should be 80 mm (3 - 1/8 in) in thickness.

Reference/starting point for brick paver installation

There are a variety of conditions that figure out the starting point of a paver project.

When beginning to set up pavers it is best to snap a real straight chalk line on the surface of the bedding sand or pull a true straight string line above the surface of the bed linen sand at the ended up elevation of the pavers This will assist as a guide for maintaining straight joint lines and will also enable the installer to make changes in the alignment of the pavers.

Buildings and concrete curbing are normally not straight and need to not be used for establishing straight joint lines. Using string lines is important to figure out the true straightness of the edge too. As the paver installation progresses, the string lines will help lessen the requirement for little trim pieces.

These will keep a minimum joint width and permit the bedding and jointing sand to enter between each paver. Pavers with spacer bars are generally not laid in snug against each other because a string line will offer constant joint spacing.

Installation of brick pavers.

One of the most commonly utilized techniques for the installation of pavers is hand installation of each paver. It is best to install a single row of pavers along one of the true straight lines that you have actually pulled or above the bed linen sand. The best method is to place a paver versus another one and let it move down into the bed linen sand.

When setting up pavers on a high grade, they must be set up at the base of the grade going uphill. This will avoid the pavers from creeping as they are being laid.

The finest way for installing pavers on large jobs is to install them mechanically. There are a couple products a specialist need to consider before setting up pavers mechanically:

1.) Mechanical installers are only capable of installing pavers in specific patterns.

2.) The professional should ensure that the manufacturer is capable of production and bundling pavers in the wanted pattern on the pallets for simple mechanical installation.

3.) Specialists may experience a color blending situation coming off the packages of pavers Poor color mixing might lead to a patchy looking installation. Many manufacturers follow color mixing on each bundle of pavers, but it is the contractor's responsibility to guarantee appropriate blending in the field.

Cutting procedures for brick pavers.

Contractors normally have 2 ways of cutting pavers. Pavers are cut either by 1). A double bladed guillotine or by 2). A gas powered cut off saw or brick saw which is equipped with a diamond blade. The diamond blade cut-off saw or brick saw will supply a much cleaner and more precise cut. Many brick saws will have a hose pipe attachment on them which will permit the operator to cut the pavers damp. When cutting pavers damp, it will assist minimize dust and will lengthen the diamond blades life. The operator of the brick saw ought to always cut the pavers far from the surface of the paver field when cutting wet, due to that the pavers will produce a slurry that will stain the paver surface. Pavers that are cut need to not fit tight, adequate spacing should be readily available for jointing sand.

The brick saw operator needs to constantly wear the correct protection that is required for operating a saw, such as eye, ear, respiratory and hand security ).

Edging types

Edge restraints play a major function in the general success of an interlocking pavement installation Edging restraints eliminate lateral motion of the pavers and hold the pavers tightly together. Especially at the outer border of the paver application, without an edging restraint, your job is guaranteed to stop working in time.

Normally produced edge restraints are the most frequently used by specialists. Produced edging restraints can vary from, plastic edging, steel and aluminum, timbers or precast concrete and stone.

Edging installation.

This could result in the migration of the bed linen sand and ultimate lateral movement of the pavers. If there is a possibility of losing bed linen sand in between the pavers and the edge restraint, then geo textile fabric is suggested. When a gap in between the pavers and the edging goes beyond 3/8" (10mm), then the space must be filled with cut pavers.

Compaction of brick pavers.

After installation, the pavers have to be compacted. The entire location that is to be compacted ought to be swept tidy of any foreign things and debris that can cause scuffing or scratching on the surface of the pavers.

In addition, it is crucial that the very first compaction takes place before any jointing sand has been used to the pavers. If jointing sand is used to the pavers before compaction takes location, this can cause a bridging issue and will not permit the joints to be completely filled with jointing sand. This can also prevent the pavers from being appropriately set into the bed linen sand.

When compacting the pavers, it is recommended that you make at least 2 passes in various instructions across the pavers. This will allow the pavers to be correctly embeded in the bed linen sand and will require the bed linen sand up into the joints from the bottom of the pavers.

The compaction of the pavers is very crucial to the final efficiency of the pavers. Failure to do correct compaction can lead to contortions and pavement failure over time.


Paver pallets/bundles ought to be put in a way not to interfere with the paver installation. One of the most extensively utilized approaches for the installation of pavers is hand installation of each paver. The operator Paver Installation Boca Raton of the brick saw should constantly cut the pavers away from the surface of the paver field when cutting wet, due to the truth that the pavers will produce a slurry that will stain the paver surface area. Edging restraints remove lateral motion of the pavers and hold the pavers tightly together. When a gap between the pavers and the edging exceeds 3/8" (10mm), then the space needs to be filled with cut pavers.

Leave a Reply

Your email address will not be published. Required fields are marked *